Fitting Cat Flap In UPVC Door Panel

Cat flaps allow your pet leave and come whenever they want without you having to let him in or out. They can also help prevent your cat from urinating in the house.

It is easier to install a cat flap on a upvc panel than on a glass one but you'll require some knowledge and appropriate tools.

Take a measurement of the door

Installing a cat flap on a door can be tricky however, as long as you use the correct type of cat flap make sure you take your time and follow the directions provided, it should not prove to be a problem. We will be showing you how much to install a cat flap to mark out the shape, use the jigsaw to slice the door's area and then finish off the job by attaching the flap to the door. This will ensure that the flap stays in place and shields the door from wind and rain damaging the door.

To determine the size of the cat flap you require, take a measurement of the width of your pet. This will let you select a flap that is big enough to allow your pet to go into the home and exit without needing to open the door every time.

If your kit has an illustration of the location to drill, you can place it on the door and then use a pencil around it. If your door has moulding or sill on the bottom of it then make sure you have clearance from these to ensure your cat flap installers's safety and will prevent them from getting access to your home.

Put on your eye protection as well as a dust mask, and using a jigsaw start to cut according to the lines you've drawn in, don't try to press the blade too hard because this could cause it to cut faster than you would like it to. If you own a set square then use it to ensure that you're cutting properly and to make sure the hole is a good rectangle shape, once you are happy with this you can start to remove the rest of the door material.

Draw a Line

The cat flap allows you to let your pet go inside and outside without having to worry about unwanted visitors or unwanted gifts. It also reduces drafts and helps to keep the temperature in your home in a stable manner. However, fitting an animal flap on your door can seem like an intimidating task for those who haven't done it before, leading many people to seek out a professional carpenter or joiner to complete the task. This is a viable option, however you can do it yourself if the tools are appropriate and the steps are followed.

Although this is much easier to do when using a timber door it is still feasible in uPVC doors, but you should be careful to avoid damaging the doors, as this can cause damage to the warranty. The first step in the process is to measure the door, ensuring that it will be able to accommodate the new cat flap. This isn't too difficult when you have a standard uPVC door, however you may need to take extra care if you are using a composite or other type of door as these are more difficult to cut into than solid upvc door panel cat flap panels.

Next, you will need to determine the height of your belly for your cat. This is the distance from the floor cat flap In upvc Door panel to the bottom of the cat's stomach and you'll need to find a place in the door that will be within the range your cat is able to comfortably walk through. Once you have this information, you will need to mark out the area using pencil and a spirit level so that you can be sure that the hole you make will be suitable for your cat.

Once you've marked the area, it is time to make the hole. You will need an jigsaw. It is important that you be patient to ensure that the cuts are smooth and straight instead of rough and uneven, as this could damage your door. Wear safety glasses and a dust mask while using the jigsaw. Inhaling sawdust can be harmful for your health. After you've finished the cutting, you'll have to smooth the edges of the hole with sandpaper, so that the cat flap can be fitted easily into place.

Make a hole

It can be difficult to fit an animal flap on a door panel or sealed double glazing unit. If you're not experienced in DIY, it is best to employ a professional to do the job for you. A mistake could not only be unsightly but also pose an security risk. It could let cold air to enter when the cat is outside and hot air out when the cat is inside.

The hole's location should be marked on the door using an eraser and a spirit level. This will ensure that it is positioned correctly and runs flush with the rest of the door. It is important to have an sandpaper piece on ready to smooth out any rough edges.

Wear the safety equipment you require when working with an electric tool. If you're concerned about the noise, you can get an electric jigsaw that is quieter and easier.

It is essential to only cut away the material needed to make the cat flap in upvc door cost flap. A little bit of extra material will be needed to cover the thickness of the the flap, but removing more than that can cause problems or cause damage to the door frame.

A upvc door may contain a metal frame or cat flap In upvc door panel panel within it that could interfere with the microchip cat flap if this is the case, you'll need to cut an over-sized hole to ensure that the metal does not come into contact with the the cat flap. If this is done, it is important to fill in the gap and make it watertight.

If you're installing the cat flap onto a upvc door or double glazed window with a frame made of metal, you will need to speak to a professional who will provide you with a new glass pane with the hole for the cat flap premade in it. It is cheaper to get this done rather than trying to fix the flap to an existing pane of glass that hasn't been designed specifically for the purpose.

Fit the Flap

Cat flaps let your pet move around at their own pace, giving them the freedom to lounge inside the house whenever they feel like it. If you've got a uPVC door, it may be difficult to install an animal flap, especially when you don't have glass panes that can be cut for one. If you're able to purchase and install a new half-glazed uPVC panel then it is possible to install a Cat Flap In Upvc Door Panel flap to these doors. It's not as simple as cutting a hole in the door, however there are a few things you'll need to do first to ensure it's safe.

A composite, uPVC or GRP door panel is usually composed of a thin plastic skin which is bonded to an insulating polystyrene core. It is important to be careful when cutting the material. This type of door typically includes a template which you can use as a guide to cut the hole in the door.

After you've marked the position of the hole in your door, now it's time to install the flap itself. You can purchase and install many different models that range from simple push-button operated models to microchip activated units that allow only your pet. Whatever kind of cat flaps you select, it's vital that your cat can use the flap without getting caught in bad weather.

A circular fitting is more effective than a square, because circles can be cut more securely into the glass. This is because square holes leave the glass vulnerable to cracking when drilling is applied to it. It's also a much safer option as you're not putting yourself at risk by drilling into toughened glass that might break and injure your pet or your family. This is particularly crucial if you have a child or an elderly person living in your home who could be hurt by shards of glass.